View AOZ1210AI_4136861.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AOZ1210
EZBuckTM 2A Simple Buck Regulator
General Description
The AOZ1210 is a high efficiency, simple to use, 2A buck regulator flexible enough to be optimized for a variety of applications. The AOZ1210 works from a 4.5V to 27V input voltage range, and provides up to 2A of continuous output current on each buck regulator output. The output voltage is adjustable down to 0.8V.
Features

4.5V to 27V operating input voltage range 70m internal NFET, efficiency: up to 95% Internal soft start Output voltage adjustable down to 0.8V 2A continuous output current Fixed 370kHz PWM operation Cycle-by-cycle current limit Short-circuit protection Thermal shutdown Small size SO-8 packages
Applications

Point of load DC/DC conversion Set top boxes DVD drives and HDD LCD Monitors & TVs Cable modems Telecom/Networking/Datacom equipment
Typical Application
VIN
C1 22F C7
VIN EN
BS LX
L1 6.8H
VOUT
AOZ1210
VBIAS
C4
R1
FB GND
R2
C4, C6 22F
COMP
RC CC
Figure 1. 3.3V/2A Buck Regulator
Rev. 1.3 December 2007
www.aosmd.com
Page 1 of 14
AOZ1210
Ordering Information
Part Number
AOZ1210AI
Ambient Temperature Range
-40C to +85C
Package
SO-8
Environmental
RoHS
All AOS Products are offering in packaging with Pb-free plating and compliant to RoHS standards. Please visit www.aosmd.com/web/quality/rohs_compliant.jsp for additional information.
Pin Configuration
LX BST GND FB
1 2 3 4 8 7 6 5
VBIAS VIN EN COMP
SO-8
(Top View)
Pin Description
Pin Number
1 2 3 4 5 6 7 8
Pin Name
LX BST GND FB COMP EN VIN VBIAS
Pin Function
PWM output connection to inductor. LX pin needs to be connected externally. Thermal connection for output stage. Bootstrap voltage input. High side driver supply. Connected to 0.1F capacitor between BST and LX. Ground. Feedback input. It is regulated to 0.8V. The FB pin is used to determine the PWM output voltage via a resistor divider between the output and GND. External loop compensation. Output of internal error amplifier. Connect a series RC network to GND for control loop compensation. Enable pin. The enable pin is active HIGH. Connect EN pin to VIN if not used. Do not leave the EN pin floating. Supply voltage input. Range from 4.5V to 27V. When VIN rises above the UVLO threshold the device starts up. All VIN pins need to be connected externally. Compensation pin of internal linear regulator. Place put a 1F capacitor between this pin and ground.
Rev. 1.3 December 2007
www.aosmd.com
Page 2 of 14
AOZ1210
Block Diagram
VIN
VBIAS
+5V
EN
UVLO & POR
5V LDO Regulator
OTP
+
ISen
-
Reference & Bias
Softstart ILimit Q1 GM = 200A/V
+ - +
BST
0.8V
+
EAmp
FB
-
PWM Comp
PWM Control Logic
LX
COMP
+ 0.2V -
Frequency Foldback Comparator
370kHz/24kHz Oscillator
Q2
GND
Absolute Maximum Ratings
Exceeding the Absolute Maximum Ratings may damage the device.
Recommend Operating Ratings
The device is not guaranteed to operate beyond the Maximum Operating Ratings.
Parameter
Supply Voltage (VIN) LX to GND EN to GND FB to GND COMP to GND BST to GND VBIAS to GND Junction Temperature (TJ) Storage Temperature (TS) ESD Rating: Human Body Model(1)
Rating
30V -0.7V to VIN+0.3V -0.3V to VIN+0.3V -0.3V to 6V -0.3V to 6V VLX+6V -0.3V to 6V +150C -65C to +150C 2kV
Parameter
Supply Voltage (VIN) Output Voltage Range Ambient Temperature (TA) Package Thermal Resistance SO-8 (JA)(2)
Rating
4.5V to 27V 0.8V to VIN -40C to +85C 105C/W
Note: 2. The value of JA is measured with the device mounted on 1-in2 FR-4 board with 2oz. Copper, in a still air environment with TA = 25C. The value in any given application depends on the user's specific board design.
Note: 1. Devices are inherently ESD sensitive, handling precautions are required. Human body model rating: 1.5k in series with 100pF.
Rev. 1.3 December 2007
www.aosmd.com
Page 3 of 14
AOZ1210
TA = 25C, VIN = VEN = 12V, VOUT = 3.3V unless otherwise specified(3)
Electrical Characteristics
Symbol
VIN VUVLO IIN IOFF VFB Supply Voltage
Parameter
Input Under-Voltage Lockout Threshold Supply Current (Quiescent) Shutdown Supply Current Feedback Voltage Load Regulation Line Regulation VIN Rising VIN Falling
Conditions
Min.
4.5
Typ.
4.3 4.1 2 3
Max.
27
Units
V V
IOUT = 0, VFB = 1.2V, VEN > 2V VEN = 0V 0.782
3 20 0.818
mA A V % %/V
0.8 0.5 0.08
IFB ENABLE VEN VHYS fO DMAX DMIN GVEA GEA ILIM
Feedback Voltage Input Current EN Input Threshold EN Input Hysteresis Frequency Maximum Duty Cycle Minimum Duty Cycle Error Amplifier Voltage Gain Error Amplifier Transconductance Current Limit Over-Temperature Shutdown Limit TJ Rising TJ Falling VFB = 0V 3.5 145 100 24 4 70 VEN = 0V, VLX = 0V 500 200 315 85 Off Threshold On Threshold
200 0.6 2.5 200 370 425 6
nA
V mV kHz % % V/V A / V
MODULATOR
PROTECTION 5.0 A C kHz ms 100 10 m A
fSC tSS RDS(ON)
Short Circuit Hiccup Frequency Soft Start Interval High-Side Switch On-Resistance High-Side Switch Leakage
PWM OUTPUT STAGE
Note: 3. Specification in BOLD indicate an ambient temperature range of -40C to +85C. These specifications are guaranteed by design.
Rev. 1.3 December 2007
www.aosmd.com
Page 4 of 14
AOZ1210
Typical Performance Characteristics
Circuit of Figure 1. TA = 25C, VIN = VEN = 24V, VOUT = 3.3V unless otherwise specified.
Light Load (DCM) Operation
Vin ripple 0.1V/div Vo ripple 20mV/div
Full Load (CCM) Operation
Vin ripple 0.1V/div Vo ripple 20mV/div IL 1A/div
IL 1A/div
VLX 20V/div
VLX 20V/div
1s/div
1s/div
Startup to Full Load
Short Circuit Protection
Vo 2V/div
Vo 2V/div
lin 0.5A/div
lL 2A/div
2ms/div
200s/div
50% to 100% Load Transient
Short Circuit Recovery
Vo Ripple 200mV/div
Vo 2V/div
lo 1A/div
IL 2A/div
200s/div
2ms/div
Rev. 1.3 December 2007
www.aosmd.com
Page 5 of 14
AOZ1210
Efficiency Curves
Efficiency
VIN = 5V 100 100
8.0V OUTPUT
Efficiency
VIN = 12V
95 Efficieny (%)
3.3V OUTPUT
95 Efficieny (%)
5.0V OUTPUT 3.3V OUTPUT
90
1.8V OUTPUT
90
85
85
80
80
75 0.2
0.4 0.6
0.8
1.0 1.2
1.4 1.6
1.8
2.0
2.2
75 0.2
0.4 0.6
0.8
1.0 1.2
1.4 1.6
1.8
2.0
2.2
Current (A)
Current (A)
Efficiency
VIN = 24V 100
95
8.0V OUTPUT
Efficieny (%)
90
5.0V OUTPUT
85
3.3V OUTPUT
80
75 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 Current (A)
Rev. 1.3 December 2007
www.aosmd.com
Page 6 of 14
AOZ1210
Detailed Description
The AOZ1210 is a current-mode step down regulator with integrated high side NMOS switch. It operates from a 4.5V to 27V input voltage range and supplies up to 2A of load current. The duty cycle can be adjusted from 6% to 85% allowing a wide range of output voltages. Features include; enable control, Power-On Reset, input under voltage lockout, fixed internal soft-start and thermal shut down. The AOZ1210 is available in SO-8 package. high-side switch is off. The inductor current is freewheeling through the Schottky diode to the output.
Switching Frequency
The AOZ1210 switching frequency is fixed and set by an internal oscillator. The switching frequency is set to 370kHz.
Output Voltage Programming
Output voltage can be set by feeding back the output to the FB pin with a resistor divider network. In the application circuit shown in Figure 1. The resistor divider network includes R1 and R2. Typically, a design is started by picking a fixed R2 value and calculating the required R1 value with equation below.
Enable and Soft Start
The AOZ1210 has an internal soft start feature to limit in-rush current and ensure the output voltage ramps up smoothly to the regulation voltage. A soft start process begins when the input voltage rises to 4.1V and voltage on EN pin is HIGH. In the soft start process, the output voltage is typically ramped to regulation voltage in 4 ms. The 4.0 ms soft start time is set internally. If the enable function is not used, connect the EN pin to VIN. Pulling EN to ground will disable the AOZ1210. Do not leave EN open. The voltage on the EN pin must be above 2.5 V to enable the AOZ1210. When voltage on EN pin falls below 0.6V, the AOZ1210 is disabled. If an application circuit requires the AOZ1210 to be disabled, an open drain or open collector circuit should be used to interface with the EN pin.
R 1 V O = 0.8 x 1 + ------ R 2
Some standard values for R1 and R2 for the most commonly used output voltages are listed in Table 1. Table 1. VO (V)
0.8 1.2 1.5 1.8 2.5 3.3 5.0 1.0 4.99 10 12.7 21.5 31.6 52.3
R1 (k)
10 11.5 10.2 10 10 10
R2 (k)
Open
Steady-State Operation
Under steady-state conditions, the converter operates in fixed frequency and Continuous-Conduction Mode (CCM). The AOZ1210 integrates an internal N-MOSFET as the high-side switch. Inductor current is sensed by amplifying the voltage drop across the drain to source of the high side power MOSFET. Since the N-MOSFET requires a gate voltage higher than the input voltage, a boost capacitor connected between the LX and BST pins drives the gate. The boost capacitor is charged while LX is low. An internal 10 switch from LX to GND is used to ensure that LX is pulled to GND even in the light load. Output voltage is divided down by the external voltage divider at the FB pin. The difference of the FB pin voltage and reference is amplified by the internal transconductance error amplifier. The error voltage, which shows on the COMP pin, is compared against the current signal. The current signal is the sum of inductor current signal and ramp compensation signal, at the PWM comparator input. If the current signal is less than the error voltage, the internal high-side switch is on. The inductor current flows from the input through the inductor to the output. When the current signal exceeds the error voltage, the
Rev. 1.3 December 2007
The combination of R1 and R2 should be large enough to avoid drawing excessive current from the output, which will cause power loss.
Protection Features
The AOZ1210 has multiple protection features to prevent system circuit damage under abnormal conditions. Over Current Protection (OCP) The sensed inductor current signal is also used for over current protection. Since the AOZ1210 employs peak current mode control, the COMP pin voltage is proportional to the peak inductor current. The COMP pin voltage is limited to be between 0.4V and 2.5V internally. The peak inductor current is automatically limited cycle by cycle.
www.aosmd.com
Page 7 of 14
AOZ1210
The cycle-by-cycle current limit threshold is internally set. When the load current reaches the current limit threshold, the cycle-by-cycle current limit circuit turns off the high side switch immediately to terminate the current duty cycle. The inductor current stops rising. The cycleby-cycle current limit protection directly limits inductor peak current. The average inductor current is also limited due to the limitation on the peak inductor current. When cycle-by-cycle current limit circuit is triggered, the output voltage drops as the duty cycle decreases. The AOZ1210 has internal short circuit protection to protect itself from catastrophic failure under output short circuit conditions. The FB pin voltage is proportional to the output voltage. Whenever the FB pin voltage is below 0.2V, the short circuit protection circuit is triggered. To prevent current limit running away when the comp pin voltage is higher than 2.1V, the short circuit protection is also triggered. As a result, the converter is shut down and hiccups at a frequency equals to 1/16 of normal switching frequency. The converter will start up via a soft start once the short circuit condition is resolved. In short circuit protection mode, the inductor average current is greatly reduced because of the low hiccup frequency. Power-On Reset (POR) A power-on reset circuit monitors the input voltage. When the input voltage exceeds 4.3V, the converter starts operation. When input voltage falls below 4.1V, the converter will stop switching. Thermal Protection An internal temperature sensor monitors the junction temperature. It shuts down the internal control circuit and high side NMOS if the junction temperature exceeds 145C. The regulator will restart automatically under the control of soft-start circuit when the junction temperature decreases to 100C. Since the input current is discontinuous in a buck converter, the current stress on the input capacitor is another concern when selecting the capacitor. For a buck circuit, the RMS value of input capacitor current can be calculated by:
VO VO I CIN _RMS = I O x --------- 1 - --------- V IN V IN
if let m equal the conversion ratio:
VO --------- = m V IN
The relationship between the input capacitor RMS current and voltage conversion ratio is calculated and shown in Figure 2. It can be seen that when VO is half of VIN, CIN is under the worst current stress. The worst current stress on CIN is 0.5 x IO.
0.5 0.4 ICIN_RMS(m) 0.3 IO 0.2 0.1 0
0
0.5 m
1
Figure 2. ICIN vs. Voltage Conversion Ratio
Application Information
The basic AOZ1210 application circuit is shown in Figure 1. Component selection is explained below. Input Capacitor The input capacitor (C1 in Figure 1) must be connected to the VIN pin and GND pin of the AOZ1210 to maintain steady input voltage and filter out the pulsing input current. The voltage rating of the input capacitor must be greater than maximum input voltage + ripple voltage. The input ripple voltage can be approximated by equation below:
For reliable operation and best performance, the input capacitors must have a current rating higher than ICIN_RMS at the worst operating conditions. Ceramic capacitors are preferred for input capacitors because of their low ESR and high ripple current rating. Depending on the application circuits, other low ESR tantalum capacitor or aluminum electrolytic capacitor may also be used. When selecting ceramic capacitors, X5R or X7R type dielectric ceramic capacitors are preferred for their better temperature and voltage characteristics. Note that the ripple current rating from capacitor manufactures is based on certain amount of life time. Further de-rating may be necessary for practical design requirement. Inductor The inductor is used to supply constant current to output when it is driven by a switching voltage. For given input and output voltage, inductance and switching frequency together decide the inductor ripple current, which is,
IO VO VO V IN = ------------------ x 1 - --------- x --------V IN V IN f x C IN
VO VO I L = ----------- x 1 - --------- V IN f xL
www.aosmd.com
Page 8 of 14
Rev. 1.3 December 2007
AOZ1210
The peak inductor current is:
I L I Lpeak = I O + -------2
High inductance gives low inductor ripple current but requires larger size inductor to avoid saturation. Low ripple current reduces inductor core losses. It also reduces RMS current through inductor and switches, which results in less conduction loss. When selecting the inductor, make sure it is able to handle the peak current without saturation even at the highest operating temperature. The inductor takes the highest current in a buck circuit. The conduction loss on inductor needs to be checked for thermal and efficiency requirements. Surface mount inductors in different shape and styles are available from Coilcraft, Elytone and Murata. Shielded inductors are small and radiate less EMI noise. But they cost more than unshielded inductors. The choice depends on EMI requirement, price and size. Output Capacitor The output capacitor is selected based on the DC output voltage rating, output ripple voltage specification and ripple current rating. The selected output capacitor must have a higher rated voltage specification than the maximum desired output voltage including ripple. De-rating needs to be considered for long term reliability. Output ripple voltage specification is another important factor for selecting the output capacitor. In a buck converter circuit, output ripple voltage is determined by inductor value, switching frequency, output capacitor value and ESR. It can be calculated by the equation below:
If the impedance of ESR at switching frequency dominates, the output ripple voltage is mainly decided by capacitor ESR and inductor ripple current. The output ripple voltage calculation can be further simplified to:
V O = I L x ES R CO
For lower output ripple voltage across the entire operating temperature range, X5R or X7R dielectric type of ceramic, or other low ESR tantalum capacitor or aluminum electrolytic capacitor may also be used as output capacitors. In a buck converter, output capacitor current is continuous. The RMS current of output capacitor is decided by the peak to peak inductor ripple current. It can be calculated by:
I L I CO _RMS = ---------12
Usually, the ripple current rating of the output capacitor is a smaller issue because of the low current stress. When the buck inductor is selected to be very small and inductor ripple current is high, output capacitor could be overstressed. Schottky Diode Selection The external freewheeling diode supplies the current to the inductor when the high side NMOS switch is off. To reduce the losses due to the forward voltage drop and recovery of diode, a Schottky diode is recommended. The maximum reverse voltage rating of the chosen Schottky diode should be greater than the maximum input voltage, and the current rating should be greater than the maximum load current.
Loop Compensation
The AOZ1210 employs peak current mode control for easy use and fast transient response. Peak current mode control eliminates the double pole effect of the output L&C filter. It greatly simplifies the compensation loop design. With peak current mode control, the buck power stage can be simplified to be a one-pole and one-zero system in frequency domain. The pole is the dominant pole and can be calculated by:
1 V O = I L x ES R CO + -------------------------- 8 x f x C O
where; CO is output capacitor value and ESRCO is the Equivalent Series Resistor of output capacitor.
When low ESR ceramic capacitor is used as output capacitor, the impedance of the capacitor at the switching frequency dominates. Output ripple is mainly caused by capacitor value and inductor ripple current. The output ripple voltage calculation can be simplified to:
1 f p1 = ----------------------------------2 x C O x R L
1 V O = I L x -------------------------- 8 x f x C -
O
Rev. 1.3 December 2007
www.aosmd.com
Page 9 of 14
AOZ1210
The zero is a ESR zero due to output capacitor and its ESR. It is can be calculated by: The strategy for choosing RC and CC is to set the cross over frequency with RC and set the compensator zero with CC. Using selected crossover frequency, fC, to calculate RC:
1 f Z 1 = ------------------------------------------------2 x C O x ESR CO
where; CO is the output filter capacitor, RL is load resistor value, and ESRCO is the equivalent series resistance of output capacitor.
2 x C O VO R C = f C x ----------- x ----------------------------V G xG
FB EA CS where; fC is desired crossover frequency, VFB is 0.8V, GEA is the error amplifier transconductance, which is 200x10-6 A/V, and GCS is the current sense circuit transconductance, which is 5.64 A/V
The compensation design is actually to shape the converter close loop transfer function to get desired gain and phase. Several different types of compensation network can be used for AOZ1210. For most cases, a series capacitor and resistor network connected to the COMP pin sets the pole-zero and is adequate for a stable high-bandwidth control loop. In the AOZ1210, FB pin and COMP pin are the inverting input and the output of internal transconductance error amplifier. A series R and C compensation network connected to COMP provides one pole and one zero. The pole is:
The compensation capacitor CC and resistor RC together make a zero. This zero is put somewhere close to the dominate pole fp1 but lower than 1/5 of the selected crossover frequency. CC can is selected by:
1.5 C C = -----------------------------------2 x R C x f p1
The equation above can also be simplified to:
G EA f p2 = -----------------------------------------2 x C C x G VEA
where; GEA is the error amplifier transconductance, which is 200 x 10-6 A/V, GVEA is the error amplifier voltage
CO x RL C C = ---------------------RC
An easy-to-use application software which helps to design and simulate the compensation loop can be found at www.aosmd.com.
The zero given by the external compensation network, capacitor CC (C5 in Figure 1) and resistor RC (R1 in Figure 1), is located at:
Thermal Management and Layout Consideration
In the AOZ1210 buck regulator circuit, high pulsing current flows through two circuit loops. The first loop starts from the input capacitors, to the VIN pin, to the LX pins, to the filter inductor, to the output capacitor and load, and then returns to the input capacitor through ground. Current flows in the first loop when the high side switch is on. The second loop starts from inductor, to the output capacitors and load, to the GND pin of the AOZ1210, to the LX pins of the AZO1210. Current flows in the second loop when the low side diode is on. In PCB layout, minimizing the two loops area reduces the noise of this circuit and improves efficiency. A ground plane is recommended to connect input capacitor, output capacitor, and GND pin of the AOZ1210. In the AOZ1210 buck regulator circuit, the three major power dissipating components are the AOZ1210, external diode and output inductor. The total power
1 f Z 2 = -----------------------------------2 x C C x R C
To design the compensation circuit, a target crossover frequency fC for close loop must be selected. The system crossover frequency is where the control loop has unity gain. The crossover frequency is also called the converter bandwidth. Generally a higher bandwidth means faster response to load transient. However, the bandwidth should not be too high due to system stability concern. When designing the compensation loop, converter stability under all line and load condition must be considered. Usually, it is recommended to set the bandwidth to be less than 1/10 of switching frequency. It is recommended to choose a crossover frequency less than 30kHz.
f C = 30kHz
Rev. 1.3 December 2007
www.aosmd.com
Page 10 of 14
AOZ1210
dissipation of converter circuit can be measured by input power minus output power. The thermal performance of the AOZ1210 is strongly affected by the PCB layout. Care should be taken by users during design process to ensure that the IC will operate under the recommended environmental conditions. Several layout tips are listed below for the best electric and thermal performance. Figure 3 is a layout example. 1. Do not use thermal relief connection to the VIN and the GND pin. Pour a maximized copper area to the GND pin and the VIN pin to help thermal dissipation. 2. Input capacitor should be connected as close as possible to the VIN and GND pins. 3. Make the current trace from LX pins to L to CO to GND as short as possible. 4. Pour copper plane on all unused board area and connect it to stable DC nodes, like VIN, GND or VOUT. 5. Keep sensitive signal traces such as the trace connecting FB and COMP pins away from the LX pins.
P total _loss = V IN x I IN - V O x I O
The power dissipation of inductor can be approximately calculated by output current and DCR of the inductor.
P inductor _loss = IO2 x R inductor x 1.1
The power dissipation of the diode is:
VO P diode_loss = I O x V F x 1 - --------- V IN
The actual AOZ1210 junction temperature can be calculated with power dissipation in the AOZ1210 and thermal impedance from junction to ambient.
T junction = ( P total _loss - P inductor _loss ) x JA + + T ambient
The maximum junction temperature of AOZ1210 is 145C, which limits the maximum load current capability.
C1
Cc
Rc
VIN
6 EN
3 GND
7 Vin
2 BST
Cb
8 VBIAS
C4
1 LX
R1
5 COMP
AOZ1210 /2
4 FB
R2
L1
Vo
C2
C 2
Figure 3. Layout Example of the AOZ1210
Rev. 1.3 December 2007
www.aosmd.com
Page 11 of 14
AOZ1210
Package Dimensions
D e 8 L Gauge Plane Seating Plane 0.25
E
E1
h x 45 1 C
7 (4x)
0.1
A2 A
b
A1
Dimensions in millimeters
2.20 Symbols A A1 A2 b c D E1 e E h L Min. 1.35 0.10 1.25 0.31 0.17 4.80 3.80 Nom. 1.65 -- 1.50 -- -- 4.90 3.90 1.27 BSC 5.80 6.00 0.25 -- 0.40 -- 0 -- Max. 1.75 0.25 1.65 0.51 0.25 5.00 4.00 6.20 0.50 1.27 8
Dimensions in inches
Symbols A A1 A2 b c D E1 e E h L Min. 0.053 0.004 0.049 0.012 0.007 0.189 0.150 Nom. Max. 0.065 0.069 -- 0.010 0.059 0.065 -- 0.020 -- 0.010 0.193 0.197 0.154 0.157 0.050 BSC 0.228 0.236 0.244 0.010 -- 0.020 0.016 -- 0.050 0 -- 8
5.74
1.27
0.80 Unit: mm
Notes: 1. All dimensions are in millimeters. 2. Dimensions are inclusive of plating 3. Package body sizes exclude mold flash and gate burrs. Mold flash at the non-lead sides should be less than 6 mils. 4. Dimension L is measured in gauge plane. 5. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact.
Rev. 1.3 December 2007
www.aosmd.com
Page 12 of 14
AOZ1210
Tape and Reel Dimensions
SO-8 Carrier Tape
D1 T See Note 5 E1 E2 E P1 P2 See Note 3
See Note 3 B0 K0 A0 Unit: mm Package SO-8 (12mm) A0 6.40 0.10 B0 5.20 0.10 K0 2.10 0.10 D0 1.60 0.10 D1 1.50 0.10 E 12.00 0.10 E1 1.75 0.10 E2 5.50 0.10 P0 8.00 0.10 P1 4.00 0.10 P2 2.00 0.10 T 0.25 0.10 D0 P0 Feeding Direction
SO-8 Reel
W1
S G M V N K
R H W W N Tape Size Reel Size M 12mm o330 o330.00 o97.00 13.00 0.10 0.30 0.50 W1 17.40 1.00 K H 10.60 o13.00 +0.50/-0.20 S 2.00 0.50 G -- R -- V --
SO-8 Tape
Leader/Trailer & Orientation
Trailer Tape 300mm min. or 75 empty pockets
Components Tape Orientation in Pocket
Leader Tape 500mm min. or 125 empty pockets
Rev. 1.3 December 2007
www.aosmd.com
Page 13 of 14
AOZ1210
AOZ1210 Package Marking
Z1210AI FAYWLT
Part Number
Fab & Assembly Location Year & Week Code
Assembly Lot Code
This datasheet contains preliminary data; supplementary data may be published at a later date. Alpha & Omega Semiconductor reserves the right to make changes at any time without notice. LIFE SUPPORT POLICY ALPHA & OMEGA SEMICONDUCTOR PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
Rev. 1.3 December 2007
www.aosmd.com
Page 14 of 14

▲Up To Search▲

Price & Availability of AOZ1210AI

	To Download AOZ1210AI Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .